Aws Visual Inspection

Posted on by



The American Society for Nondestructive Testing (ASNT) has an agreement with the American Welding Society (AWS) to provide access for AWS Certified Welding Inspectors (CWIs) and Senior Certified Welding Inspectors (SCWIs) to Visual. Approved for the project. Visual inspection should be conducted by appropriately qualified personnel, in accordance with a written practice. 10.1 Personnel Qualification Visual inspection personnel should be qualified under AWS D1.1, Chapter 6. The basis of qualification should be specified by the Engineer. Acceptable qualification bases are. If AWS D1.1 is the code that covers the welding performed,then yes the welder and weld inspector should visually inspect all welds according to Table 6.1 (Visual Inspection Acceptance Criteria) By jon20013 Date 18:45. The controlling specifications AWS D17.1 and the WS33739 (base document only excluding appendices.) Specific guidelines for other specifications examples such as AWS D1.1 and AWS D1.2 are discussed in paragraph 4.11. This Visual Weld Inspection.

Visual examination of weld joint is an important activity, carried out to check the integrity and soundness of the weldment. It is an economical activity, as it doesn’t require any costly equipment. It must be carried out by a well experienced inspector. Main responsibilities of a welding inspector are:

Aws Visual Inspection
  • Code compliance
  • Workmanship control
  • Documentation Control

The requirements of visual examination are:

  1. Illumination should be at least 350 Lux (minimum) but it is recommended to carry out visual inspection at an illumination of more than 500 Lux.
  2. The inspectors eye should be within the radii of 600 mm of the surface of item being inspected and the viewing angle must not be less than 30 degrees.

(Also read Thickness range for welder qualification test)

Other aids which may be required during visual examination are:

  • Welding gauges (Figure 2a and 2b)
  • Weld gap gauges
  • Linear misalignment gauges (Hi-Low)
  • Magnifying glass (X2 to X5)
  • Mirrored boroscope or fibre optic viewing system (when access is restricted)

Visual inspection can be done at three stages;

  • Before welding,
  • During welding and
  • After welding

Before Welding: The inspector shall be familiarized with the applicable codes and standards/drawings/welding procedures (WPS and PQR). Welder qualification shall be carried out before production welding. The inspector shall confirm the material and review the MTC. Welding consumables shall also be inspected before welding. Joint preparation and alignment shall also to be checked prior to welding. After confirmation of all the parameters (as mentioned above), the welding inspector can permit the welder to start the production welding. If preheat is applicable, then the preheat temperature shall be confirmed before starting the weld.

(Figure 3 shows improper groove face and root gap, a welding inspector must see the groove preparation and root gap before welding)

During Welding: The inspector shall check the welding process and welding parameters with respect to the welding procedure specification (WPS) at any time during welding. Root run and root run dressing, interpass temperature shall be witnessed by the inspector. The welding consumables shall also be checked during welding.

(Also read How to write a welding procedure specification – WPS)

After welding: After complete welding, identification number is punched near joint. Complete visual inspection is done and any surface breaking or defect shall be repaired as per approved procedure. Following defects (or discontinuity) can be revealed by visual inspection:

(Figure 4: Welding inspector checking the weld reinforcement size by a Bridge Cam welding Gauge)

A dimensional survey shall be done to ensure the dimension of the part after welding. After satisfactory completion of welding proper documentation is prepared.

If a Post weld treatment is specified in WPS, Then the operation should be monitored and documented. Following parameters to be considered when Post weld heat treatment is required,

  1. Area to be heated
  2. Heating and cooling rates
  3. Holding temperature and duration
  4. Temperature distribution

Aws Visual Inspection Kit

In addition to visual inspection, a number of other NDT (Non Destructive Test) methods are available to check the quality of weldment, some of the most common NDT methods are;

  1. Magnetic particle testing (MT)
  2. Electromagnetic testing (ET)
  3. Acoustic emission testing (AET)

Aws Visual Inspection Of Welds

Each NDT methods has its own significance and importance for example Liquid penetrant testing is very efficient and economical for checking surface defects, whereas, with the help of Ultrasonic test and Radiography test, entire depth of the weld can be inspected.

Selection of NDT methods depend on the requirements. Person engaged or assigned to carry out these tests must possess the necessary qualification. A written test procedure, format for reporting and the applicable code must also be decided before conducting the examination.

Aws Inspector Cost

Also read P-number, F-number and A-number in welding (ASME Section IX)

Aws Visual Inspection Procedure

Note: I had written this article for India welds newsletter- Vol 1:4 Oct-Dec 2018. Click here to read that newsletter.